Environmental soil testing is the laboratory analysis of soil samples from a site to determine whether they contain contaminants at concentrations exceeding regulatory standards. It differs from agricultural soil testing, which measures fertility, and geotechnical soil testing, which assesses load-bearing capacity for construction.
This practical guide explains when your facility needs soil testing, how samples are collected correctly, what is tested, and how to interpret the results.
Three Types of Soil Testing: Which Do You Need?
| Type | Purpose | Who Needs It |
|---|---|---|
| Environmental testing (the focus of this article) | Detecting contaminants | Factories, gas stations, workshops, warehouses, and buyers of industrial sites |
| Agricultural testing | Measuring fertility and nutrient levels | Farms |
| Geotechnical testing | Assessing load-bearing properties for construction | Construction projects |
When Does Your Facility Need Environmental Soil Testing?
- Before buying or leasing an industrial site: To determine whether it is contaminated before assuming responsibility for it.
- When closing or relocating operations: To document the site's condition and meet closure requirements.
- After a leak or spill: To determine the extent of contamination.
- As part of an environmental impact assessment or environmental audit: When soil quality assessment is required.
- When requested by the Center: The soil regulation requires information on contamination levels to be provided upon request.
- Before and after remediating contaminated soil: To design the remediation approach and then verify its success.
Examples by Activity: Where to Look and What to Test For
| Activity | Priority Sampling Locations | Likely Contaminants |
|---|---|---|
| Gas station | Around underground tanks, connecting pipelines, and the pump area | Petroleum hydrocarbons |
| Auto repair shop | Oil change areas, used oil storage areas, and floor drains | Oils and heavy metals |
| Chemical or paint factory | Storage and loading areas, and locations of previous spills | Solvents and heavy metals, depending on the materials used |
| Warehouse | Hazardous material storage areas, and generator and fuel areas | Depends on materials stored historically, not just those currently stored |
| Farm or rural site | Pesticide mixing and storage areas | Pesticide residues |
The principle is always the same: collect samples where activities took place, not where digging is easiest.
How Are Soil Samples Collected?
The quality of the results depends on the quality of the sample. Sampling errors are more common than laboratory errors.
1. Sampling Plan The plan is based on the site's history: Where were the tanks? Where were materials stored? Where did leaks occur? It then defines:
- Sampling points: In suspected contaminated areas, with reference points in clean areas for comparison.
- Depths: Both shallow and deeper samples, because some contaminants migrate downward.
- Number of samples: Enough to map the extent of contamination—not just one sample.
2. Field Sampling Samples are collected using clean tools and containers appropriate for the type of analysis. The location, depth, and time are documented, and the chain of custody is maintained through delivery to the laboratory.
3. Preservation and Transport Some volatile contaminants can be lost if samples are not kept refrigerated and tightly sealed.
What Is Tested in Environmental Soil Analysis?
Testing parameters are selected according to the site's activities, rather than using a fixed list for every site:
| Contaminant Group | Examples | Commonly Tested At |
|---|---|---|
| Petroleum hydrocarbons | Diesel, gasoline, and oils | Gas stations, workshops, and tank locations |
| Heavy metals | Lead, cadmium, chromium, mercury, and arsenic | Metal, coating, and battery factories |
| Volatile organic compounds | Solvents | Paint and chemical factories, and printing facilities |
| Pesticides | Insecticides and herbicides | Former agricultural sites |
| Soil properties | pH, salinity, and particle size | All sites, to help interpret the results |
How Do You Interpret Soil Test Results?
Results are compared with the standards in Annex (1) of the Executive Regulation for the Prevention and Remediation of Soil Pollution. These standards depend on two factors:
- Soil type: Coarse soil (sand and gravel, with particles 75 microns or larger) or fine soil (silt and clay, with particles smaller than 75 microns). This is why particle size is measured as part of the analysis.
- Land use: Standards differ by land use. What is acceptable on industrial land may not be acceptable on residential land.
The rule: If any contaminant exceeds the standard specified for the soil type and land use, the site is considered to have contaminated soil, and the Center must be notified and the site remediated.
What Happens After the Results Are Available?
- All results are below the standards: The report is documented and retained. It serves as evidence if you are later asked about the site's condition, particularly during a sale or closure.
- One or more results exceed the standards: A result alone does not mean the entire site is contaminated. The next step is to determine the extent of contamination through additional horizontal and vertical sampling.
- After determining the extent: A remediation or rehabilitation plan is prepared, defining the method, objective, and monitoring requirements. Read Detecting and Remediating Contaminated Soil.
- After remediation: Verification samples demonstrate that the objective has been achieved and are included with the closure report.
If contamination resulted from a recent incident, the response begins before testing: contain the source and notify the competent authority if the incident is reportable. Read Environmental Incidents and Emergencies.
Who Conducts Soil Testing?
- Laboratory analysis: An accredited environmental laboratory.
- Sampling plan design, results interpretation, and remediation planning: A licensed environmental service provider.
- For studies submitted to the Center: The regulation requires analyses and measurements to be performed by an environmental service provider licensed by the Center.
Common Soil Testing Mistakes
- Taking one sample from a random point instead of following a plan based on the site's history.
- Testing general parameters unrelated to the site's activities and overlooking the actual contaminant.
- Collecting only surface samples when contamination is deeper underground.
- Comparing results with an incorrect standard that does not match the soil type or land use.
Checklist Before Buying or Leasing an Industrial Site
- Request the site's land-use history: What activities did previous owners carry out?
- Ask about current and former underground tanks and their locations.
- Request previous environmental permits and monitoring and inspection reports, if available.
- Inspect the site for oil stains, discolored soil, or abandoned drums.
- If there are any warning signs, make soil testing a condition before signing.
- Specify in the contract who is responsible for remediating any preexisting contamination discovered later.
For contractual details, read Facility Ownership Transfer and the Environmental Permit.
What Should the Report Include?
A laboratory certificate alone is not a report. A report that stands up to review includes:
- A site map showing sampling points and depths, with the reason for selecting each point.
- The sampling date, the identity of the sampler, and the chain-of-custody record.
- The laboratory's name and license, analytical methods, and detection limits.
- A table comparing results with the appropriate standard for the soil type and land use.
- The conclusion and recommendation: a clean site, further delineation, or remediation.
Key Terms
- Discrete sample: A sample from a single point and depth that represents only that point.
- Composite sample: A mixture of several samples from one area. It provides an average and does not identify a contaminated hotspot within that area.
- Reference point: A sample from a clean area near the site, used to compare results and determine natural background conditions in the area.
- Chain of custody: A record documenting who collected the sample, who transported it, and when it arrived at the laboratory, to protect the credibility of the result.
- Detection limit: The lowest concentration the laboratory can measure. If it is higher than the regulatory standard, a “not detected” result proves nothing.
- Delineation: Additional sampling to map the horizontal and vertical boundaries of contamination before remediation.
How Can Abak Green Help?
We design a sampling plan based on your site's history and activities, coordinate testing through an accredited laboratory, interpret the results against regulatory standards, and prepare a clear report: Is the site contaminated? What is the extent of contamination? What is the next step? If remediation is required, it falls within the scope of our official license.
Site Rehabilitation and Contaminated Soil Remediation Plans · Soil Contamination · Request a Soil Testing Plan for Your Site
Frequently Asked Questions About Soil Testing
What is the difference between environmental and agricultural soil testing?
Environmental testing detects contaminants, while agricultural testing measures fertility and nutrient levels.
How many samples do I need to test soil at an industrial site?
The number depends on the site's area and the number of potential contamination sources, and is determined in the sampling plan.
Which contaminants are tested for in soil?
Testing depends on the site's activities. Common contaminants include petroleum hydrocarbons, heavy metals, and volatile organic compounds.
What are soil test results compared against?
The standards in Annex (1) of the Regulation for the Prevention and Remediation of Soil Pollution, according to soil type and land use.
Do you test soil in your own laboratory?
Laboratory analysis is conducted through an accredited laboratory. We design the plan, interpret the results, and prepare the report.
What should I do if testing reveals contamination?
Notify the Center, then determine the extent of contamination and prepare a remediation and rehabilitation plan.
Is one sample enough to prove that a site is clean?
No. One sample represents only its sampling point. Establishing the site's condition requires a sampling plan based on its history and the locations of its activities.
What happens if a result exceeds regulatory standards?
The boundaries of contamination are determined through additional sampling. A remediation or rehabilitation plan is then prepared, and its results are confirmed through verification sampling after implementation.
Do I need soil testing before buying an industrial site?
If the site was used for an activity that could contaminate soil, testing before purchase protects you from assuming responsibility for contamination you did not cause.